MDMA 1.1.0.2

MDMA - a Mobile Data Monitoring Application version 1.1.0.2 2014/06/27

======================================================================



Before running MDMA make sure you have no other applications or dashboards

open that might be using your data device's communications port.

Many dashboard applications drop the connection when you close them;

you can use Ctrl-Alt-Del to pop up the Windows Task Manager, select the

dashboard application and click on the End Task button, and your internet

connection will remain open. When you are finished with MDMA you can close

it without dropping your connection and open your dashboard again.

Doing this will keep your data counters running. You can use your dashboard

application or MDMA to keep track of your usage, but not both. Be sure to

disconnect your internet connection from the program in which you wish to

track your usage.

Most dashboard applications use the autorun mechanism to start their dashboard

when the modem is inserted, to temporarily stop this behaviour, hold down the

Shift key down while inserting the modem. For a more permanent fix, you can

disable autorun in your registry or prevent the emulated CD-ROM from being

assigned a drive letter in Disk Management. See:

http://mybroadband.co.za/vb/showthread.php/59080?p=1552315#post1552315

Additionally, some recent dashboards also install a service that starts their

dashboard, simply disable thse services to prevent his behaviour.

Service names to look out for are 'DCservice.exe',

'Vodafone Mobile Broadband Service' and 'UI Assistant Service'.



Signal group

============

On the left is the Received Signal Strength Indicator (RSSI) in dBm, measured

between -113dBm and -51dBm.

Next Mobile Country Code (MCC) and Mobile Network Code (MNC) of the operator

to which your modem is registered.

Next is the operator's long alphanumeric name. Depending on device and

SIM card, this information might not be available.

On the right is the Radio Access Technology; GPRS, EDGE, 3G, HSDPA, HSUPA

or HSD+UPA (High Speed Downlink and Uplink). It is normal for the HSxPA

indicators to only appear while data is being transmitted and while the

connection is idle, 3G or WCDMA is displayed.

Below this is a bar graph indicating the signal strength.

The next line of information is information from the current base station;

the Location Area Code, the Radio Network Controller Identifier (RNC ID),

the Cell Identifier and checkboxes indicating whether the modem is currently

registered and roaming.

Recent Huawei modems also provide SNR values but it is not clear what they

represent. Further information here:

http://mybroadband.co.za/vb/showthread.php/389765?p=7437935#post7437935

I now think that these two SNR values are the RSCP and Ec/Io respectively.

Further information on signal strength (RSSI):

http://mybroadband.co.za/vb/showthread.php/61703



Data Counters group (Huawei devices only)

=========================================

The volume of data transmitted and received in the current and last session

is shown here. You can track your total usage here as well. The totals are

stored in a file called 'usage.bin' located in the 'Common AppData' folder

on your computer (normally

C:\Documents and Settings\All Users\Application Data\MDMA in Win2K/XP,

or C:\AppData\MDMA in Vista/Win7).

The 'Reset Session' button zeroes the current session data counters and adds

to the totals, useful if you want to measure exactly how much bandwidth a

particular operation uses. The 'Reset Total' button zeroes the totals,

you can use this when you top-up or get a new data bundle or on your contract

billing day.



Data Transfer Speed group (Huawei devices only)

===============================================

Here you can see your current upload and download speeds as well as the

highest peak recorded. There is also a 10 second moving average which shows

the average upload and download speed over the last 10 seconds. There are

reset buttons for the peaks and the averages, these do not affect the data

counters.

If avilable, the negotiated QoS is also indicated here; this can vary

according to your data plan, your modem, and even the particular base station

you are attached to.



Connection Type group

=====================

Here you can switch your connection type between GPRS/EDGE Only,

GPRS/EDGE Preferred, 3G/HSPA Only, or 3G/HSPA Preferred.

This does not reset the modem and you can do this and stay online,

provided you have coverage of the signal type you requested.

For example, you could switch from 3G/HSPA to GPRS/EDGE to capture cellular

broadcasts and then switch back to 3G/HSPA.

This function works much better on Huawei cards; some older Option and Novatel

cards or drivers sometimes require the card and/or your computer to be

restarted before you can use them again. LTE modems also have the option

of LTE Only and, LTE and 3G/HSPA Only (i.e. no GPRS/EDGE).



APN group

=========

You can view and set your default APN here, much easier than using a modem

initialization string. If your modem does not have a default APN configured,

it is automatically set to 'internet'.



USSD Commands group

===================

You can enter USSD commands here, these are commands in the form *123# that

are normally entered on your mobile phones's keypad.

Clicking on 'USSD Help' will display a brief listing of some USSD commands

offered by your operator (if available).

Sending a USSD command creates a session, some USSD services are billable,

when you are finished, click the End Session button.

USSD commands that don't require any further input automatically end the

session, in which case the End Session remains greyed out.

You can send multiple USSD commands sepeated by commas,

for example: *111#,1,6 for Vodacom pre-paid data bundle balance.

MDMA will wait for a response before sending the next command.



Cellular Broadcast Messages group

=================================

Received cellular broadcast messages such as cell info, weather reports and

base staion info are shown here.

Not all operators provide 3G cell broadcasts, you might need to switch your

evice in GPRS/EDGE Only mode to receive them.



Start/Stop Logging

==================

This function logs signal strength, connection type, LAC, Cell ID and cellular

broadcast messages to a comma-seperated-values (CSV) file.

The signal strength is recorded in its raw format, as a number from 0 to 31

or 99 for no signal. To convert this number to dBm, multiply it by 2 and

subract -113. LAC and Cell IDs are recorded in hexadecimal.



Device Info

===========

This interrogates your data device and SIM card, not all devices and SIM cards

provide all of the information.



About

=====

Some information about the program.



Reset Device

============

This instructs your device to do a full reset, you should notice that the

device disappears from your operating system and gets detected again.

Some older cards or drivers do not recover from a full reset gracefully

and require you to restart your computer before they become operational again.



Connect / Disconnect

====================

This allows you to connect and disconnect from the internet using a network

device (NDIS) or a dial-up networking (RAS) connection.

MDMA will use NDIS if available, otherwise fall back to RAS by executing

'rasphone.exe -d MDMA'. Rasphone is a command line tool for dial-up

networking which is part of your Windows installation. You must have a

dial-up networking connection named 'MDMA' otherwise you will see the

following message: 'Error 623: The system could not find the phone book entry

for this connection.'.

The behavior can be changed to that of older versions of MDMA

(1.0.0.31 and earlier) by using the /dialmode command line switch

(see command line options below).

When you are online the button changes to Disconnect which disconnects the

modem in the proper manner and reset the data counters for the current session

and adds to the totals. (Huawei devices only)



Band Config

===========

This allows you finer control of the bands used by the modem than the

Connection Type described above. Depending on your modem, you can enable and

disable individual or groups of bands, e.g. GSM 900, UMTS 2100.

This is currently available for Huawei and Sierra Wireless modems.

Band configuration of ZTE modems is currently disabled due to reports

of these modems not enabling UMTS 900 when set to default settings.

This can be enabled using a command line switch (at your own risk!).



Support

=======

Community support is available on MyBroadband forum in the following thread:

http://mybroadband.co.za/vb/showthread.php/59080



Command line options

====================

/? displays command line help



/port:COM<x> skip device autodetection and use the specified port

if /commandset is not specified, only 3GPP standard commands are used



/commandset specify which command set to use, overriding automatic detection

<command set> may be:

Standard, Huawei, Option, Novatel, Sierra, Nokia, ZTE, Icera

Longcheer or Dlink



/ussd:<mode> specify the USSD decoding mode, overriding automatic decoding

<mode> may be:

Plain, PDU, Hybrid (send Plain/receive PDU), Packed7 or Unicode



/opsel:<mccmnc> select manual or automatic network operator selection

where <mccmnc> is the network operator's MCC/MNC for manual,

or 0 for automatic



/sessionlog keeps a log of data used per session



/speedlog keeps a log of signal information and transfer speeds



/diaglog enable diagnostic logging



/hexqos enables display of QoS values in raw hexadecimal format (debug)



/nopollcid do not poll Cell ID (debug)



/nocbm do not enable CBM reception (debug)



/hwunlock:<code> send 6 or 8-digit network operator unlock code (Huawei only)



/hwstorage:<x> send ^U2DIAG command to control emulated CD-ROM and Micro-SD card (Huawei only)

values of <x> for most devices:

0: disable CD-ROM and Micro-SD

1: enable CD-ROM only

255: enable CD-ROM and Micro-SD

256: enable Micro-SD only



/zstorage:<x> send +ZCDRUN command to control emulated CD-ROM and Micro-SD card (ZTE only)

some known values of <x>:

8: disable autorun (modem appears when plugged in)

9: enable autorun (only CD-ROM appears when plugged in)

E: enable download mode (CD-ROM does not appear when

plugged in)

F: disable download mode (CD-ROM appears when plugged in)



/zband enable band configuration window (ZTE only)



/swregion:<x> set PRL region for band scanning (Sierra Wireless only)

some known values of <x>:

0: All Regions

1: Europe

2: North America

3: Australia

4: Japan



/dialmode:<mode> specify the dial mode instead of using NDISDUP if available, or a RAS connection

named MDMA, where <mode> may be:

RAS: pop up a dialog for choosing a RAS connection

(as in MDMA 1.0.0.31 and earlier)

MDMA: only use a RAS connection named MDMA

NDISDUP: only use NDISDUP



/nopolling do not poll the modem at all (passive mode)



/atf0init send AT&F0 during initialization (as in MDMA 1.1.0.1 and earlier)

----------
Dikirim dari Nokia Asha 308

0 Response to "MDMA 1.1.0.2"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel